C7 ACERT™ Water-Cooled Manifold Engine

C7 ACERT™ Water-Cooled Manifold Engine

Length 44 in.
Width 34 in.
Height 44 in.
Weight 1,570 lb
Lube Oil System (refill) 5 gal
Minimum Rating 205 BHP
Dimensions
Length 44 in.
Width 34 in.
Height 44 in.
Weight 1,570 lb
Length 44 in
Width 34 in
Height 44 in
Weight 1,570 lb
Capacity for Liquids
Lube Oil System (refill) 5 gal
Lube Oil System - Refill 5 gal (US)
General Specifications
Minimum Rating 205 BHP
Maximum Rating 275 BHP
Governor and Protection Electronic (ADEM™ A4)
RPM 2,200 r/min
Aspiration Turbocharged-Aftercooled
Displacement 442 in³
Flywheel and Flywheel Housing SAE 1, 2, or 3
Flywheel Teeth 156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
Rotation from Flywheel End Counterclockwise
Stroke 5 in
Bore 4 in
Emissions
Emissions EPA & CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II

Technology

- Electrical harness containing point-to-point wiring without splices in any power/signal wires - Electrical harnesses and connectors are overmolded and are routed through urethane tube for protection against impact and vertical flame propagation. - To meet safety requirements, connectors require the use of a special tool to be disconnected and bear the “do not disconnect while energized” warning. - Optional ATEX and NEC certified 25-foot customer harness - ECU is certified as part of the engine to restricted breathing per EN 60079-15. ECU is protected with a stainless steel guard. - Fuel injector connections at valve cover bases are protected with stainless steel guards

Advanced Digital Engine Management

ADEM A4 engine management system integrates speed control, air/fuel ratio control and ignition/detonation controls into a complete engine management system. control system with integrated digital ignition, engine protection and monitoring

Air System

- Separate circuit (water-to-air) aftercooler options available to match any application requirement. - Water-cooled exhaust manifold and turbo maintain ATEXcompliant skin temperature during operation

Improved Serviceability

- Front, right, and rear dipsticks - Remote oil and fuel filters - 12V and 24V electronic systems to improve application flexibility

Custom Packaging

Trust a Cat factory custom package to meet your exact petroleum application needs. Cat engines, generators, enclosures, controls, radiators, transmissions — anything your project requires — can be custom designed and matched to create a one-of-a kind solution. Custom packages are globally supported and are covered by a one-year warranty after startup.

Full Range of Attachments

Large variety of factory-installed engine attachments reduces packaging time

Testing

Every engine is full-load tested to ensure proper engine performance.

Product Support Offered Through Global Cat Dealer Network

More than 2,200 dealer outlets -Cat factory-trained dealer technicians service every aspect of your petroleum engine -Cat parts and labor warranty Preventive maintenance agreements available for repair-beforefailure options -S•O•SSM program matches your oil and coolant samples against Caterpillar set standards

Over 80 Years of Engine Manufacturing Experience

Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.

Over 80 Years of Engine Manufacturing Experience

Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.

Web Site

For all your petroleum power requirements, visit www.catoilandgasinfo.com.

Web Site

For all your petroleum power requirements, visit www.catoilandgasinfo.com.

  • Air Inlet System
    • Turbocharger, separate circuit (SCAC)
    • Single, right-side, center-mounted turbo with water-cooled turbine housing
    • Air inlet, RH side, rear facing, 101.6 mm (4 in.) connection type
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Fuel cooled ECU
    • Power compensation for fuel temperature
    • Programmable low and high idle
    • Electronic diagnostics and fault logging
    • Programmable monitoring system (engine speed, temperature, pressure)
    • J1939 broadcast (diagnostic and engine status)
    • Certified electrical control system
    • Derated engine: automatic ambient temperature compensation
  • Cooling System
    • Thermostats and housing, front-facing outlet — 51 mm (2.01 in) connection
    • Jacket water pump — belt-driven, centrifugal
    • Water pump — inlet RH front vertical inlet (pointing down) — 63 mm (2.48 in)
  • Exhaust System
    • Single, right-side, center-mounted turbo with water-cooled turbine housing
    • Exhaust manifold — water-cooled
    • Front turbo exhaust
  • Flywheels And Flywheel Housing
    • Mandatory selection of: SAE No. 1, SAE No. 2, or SAE No. 3 flywheel and housing SAE standard rotation
  • Fuel System
    • HEUI fuel system
    • Fuel filter — secondary, LH front (2-micron high performance)
    • Fuel transfer pump — left front
    • Fuel priming pump — left front
  • Lube System
    • Crankcase breather — top rear
    • Crankcase fumes disposal — RH
    • Oil cooler — RH
    • Oil filter — RH
    • Oil pan — front sump, 31 L (33 qt) oil change capacity
    • Oil filler — front top valve cover
    • Oil level gauge — LH rear
    • Engine oil pump — gear-driven
    • Oil valve sampling, RH
  • Power Take-offs
    • Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
  • General
    • Vibration damper
    • Lifting eyes
    • Literature
    • No paint
  • Mandatory Options
    • Flywheel housing and flywheel
    • Primary filter/water separator
    • Turbo orientation
  • Air Inlet System
    • Precleaner
    • Air Inlet elbow
  • Cooling System
    • Water outlet elbow
    • Coolant conditioner
  • Emissions Certifications
    • IMO certification
  • Flywheels And Flywheel Housing
    • Crankshaft seal
  • Instrumentation
    • Gauges and instrument panels
  • Lube System
    • Oil pans
    • Drain and cover
    • Remote oil filters
    • Lubricating oils
  • Mounting System
    • Structural steel base
    • Engine support -- front and rear
  • Power Take-offs
    • Crankshaft pulleys
  • General
    • Tool set
×