Cat C32 Auxiliary/Generator Set Engine (IMO II)

Cat C32 Auxiliary/Generator Set Engine (IMO II)

Minimum Rating 791 bhp
Aspiration TTA
Configuration Vee 12, 4-Stroke-Cycle Diesel
Bore 6 in
Stroke 6 in
Displacement 1,959 in3
Power Rating
Minimum Rating 791 bhp
Maximum Rating 1,333 BHP
Minimum Rating 791 BHP
Engine Specifications
Aspiration TTA
Configuration Vee 12, 4-Stroke-Cycle Diesel
Bore 6 in
Stroke 6 in
Displacement 1,959 in3
Rotation (from flywheel end) Counterclockwise
Aspiration TTA
Bore 6 in
Configuration Vee 12, 4-Stroke-Cycle Diesel
Displacement 1,959 in³
Rotation from Flywheel End Counterclockwise
Stroke 6 in
Dimensions & Weights
Minimum Length 84 in
Maximum Length 90 in
Width 60 in
Minimum Height 61 in
Maximum Height 63 in
Minimum Dry Weight 6,950 lb
Maximum Dry Weight 7,160 lb
Maximum Dry Weight 7,160 lb
Maximum Height 63 in
Maximum Length 90 in
Minimum Dry Weight 6,950 lb
Minimum Height 61 in
Minimum Length 84 in
Width 60 in

Emissions

IMO II compliant for all ratings

Worldwide Support

Extensive service network of dealers; Unparalleled service from authorized marine dealers

Durability

Proven engine operating history; Performance iron with thousands of hours of validation testing for quality and durability

Reliability

60 months standard warranty

Cooling System

Heat Exchanger or Keel Cooling; Heat exchanger configurations: optional front mounted sea water pump

Aftercooling System

Separate circuit aftercooling system (SCAC): no seawater circulating through the aftercooler

  • Air Inlet System
    • Separate circuit after-cooled (SCAC)
    • Air cleaner
    • Turbocharger, jacket water cooled
    • Turbocharger inlet, 152 mm (6 in) OD straight connection
  • Control System
    • Programmable Low Idle (550 - 750 rpm)
    • Programmable High Idle Limit for WOSR Ratings
    • Electronic diagnostics and fault logging
    • Engine and transmission monitoring (speed, temperature, pressure)
    • Electronic fuel/air ratio control
    • Engine Protection Mode for extended ambient conditions
    • 70-pin customer connector
    • Throttle Input signal options
    • 0 - 5 Volts
    • 4 - 20 mA
    • PWM (Pulse Width Modulated)
  • Cooling System
    • Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
    • Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines
    • SCAC pump, gear driven
    • Jacket water pump, gear driven
    • Sea water pump, bronze impeller, gear driven, when selected for Hex cooled engines
    • Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection
    • Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt
    • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • Exhaust System
    • Water-cooled exhaust manifold & turbocharger
    • 4 Bolt 130 mm (5.12 in) diameter flanged outlet
  • Flywheels & Flywheel Housings
    • SAE standard rotation (CCW facing exciter end)
    • Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth
  • Fuel System
    • Duplex Fuel Filters, Spin-on, RH & LH service
    • Fuel connections size: r driven
    • Plate-type fuel cooler installed behind Aftercooler Shunt Tank
    • Fuel transfer pump, gear driven
    • Manual fuel priming pump
    • Hybrid fuel line design
  • Lube System
    • Simplex Oil Filters, RH or LH service
    • Deep sump oil pan
    • RH or LH service oil filler locations
    • RH or LH service dipstick
    • Oil pump, gear driven
  • Mounting System
    • Front support - 33 inches wide
  • Power Take-offs
    • Front Poly-V groove pulley (Quantity 1) for auxiliary drives
  • General
    • Common electrical bonding point
    • Engine does not ship with zinc components
  • Exhaust System
    • Dry Elbows
    • Flexible Fitting
    • Flange
    • Muffler
    • Muffler Spark Arresting
  • Air Inlet System
    • Air Inlet Adapter
  • Charging System
    • Battery Chargers
    • Charging Alternators
    • Ammeter
  • Control System
    • Load Sharing Attachment
    • Instrument Panels
    • Caterpillar Alarm Protection
    • Fuel and Oil Shielding
  • Fuel System
    • Water Separator
  • General
    • Fumes Disposal System
  • Instrumentation
    • Instrument Panels
    • OEM Wiring Harness
    • Engine to Engine Harness
    • Gauges
    • Transmission Sensors
    • Exhaust Temperature Sensors
  • Lube System
    • Duplex Oil Filters
    • Sump Pump
  • Power Take-offs
    • Rear Hydraulic Pump Drive
  • Starting System
    • Electric Starting Motors - Single 24 Volt
    • Air Starting Motor
    • Dual Starting Motors (Electric and Air)
    • Air Start Accessories
    • Starting Aids - JW Heaters
    • Battery Sets - 24 Volt - Dry
  • Mounting System
    • Front Support
    • Rear Support
    • Isolators Mounts
    • Adapter Kits
  • Packing
    • Engine Protective Cover
    • Storage Preservation
    • Export Packing
×